交流伺服电机进行驱动是目前成形技术装备企业发展的一个新方向。油压热压机适用于FPC(柔性线路板),HSC(斑马纸),TAB与LCD及PCB的连接。 由于消费类电子产品中PCB或FPC的Pitch趋于细小化,传统锡焊工艺已经难以满足极细热压的...
2023-02-16防止小型热压机空气进入和汽蚀的方法 1)防止空气混入 装满油后,油箱油位要始终保持不低于油位指示线,尤其是在安装时 有大型液压缸的液压控制系统,除第一次中国加入自己足够的油液外,当启动一个液压缸, 油进入一个液...
2023-02-15防止热压机油压冲击的一般方法 ①对于阀口突然关闭过程中产生的压力不断冲击,可采取下述研究方法进行排除或减轻: . 减慢换向阀的关闭速度,即增加换向时间魔术。多层热压机厂家控制阀:控制液压油的流量,流向,压力,...
2023-02-15防止热压机液压冲击的一般方法 ①热压机对于阀口突然出现关闭过程中产生的压力不断冲击r可采取具有下述研究方法进行排除或减轻 A.减慢换向阀的关闭中国速度,即增大换阳时间to例如可以采用一个直流系统电磁阀比交流的液压...
2023-02-15翻车机压梁热压机液压系统不能自锁故障的分析与排除。生产硫化机厂家压制时,摸具必须放在垫板中心位置,禁止偏心使用。每班开机前,试压后,应检查一次模具是否有裂损。数控热压机最后通过单向阀使液压油在油箱循环使...
2023-02-15电液换向阀过渡功能引起热压机故障分析及排除 在热压机的高压大流量系统中,由于液压系统对换向阀中心的稳定作用,传统电磁换向阀的电磁力较大 一般都比较小,无法保证其可靠换相。热压机厂家脉冲加热原理,由于焊头表面...
2023-02-15电液比例控制阀的原理和结构 电液比例控制阀是一种方法能使所输出油液的参数(压力、流量和方向)随输入电信号参数(电 流、电压〉的变化发展而成比例不断变化的液压控制阀,它是作为一种集开关式电液控制作用元件和伺服式电...
2023-02-15单级单吸悬臂离心泵 它适用于企业输送清水或物理及化学结构性质进行类似清水的其他工作液体之用,温度不高于80C。金属热压成型机操作者应熟悉油压机的一般性能和结构,禁止超负荷使用。东莞热压成型机基本投资省,占地面...
2023-02-15大型热压机制动系统蓄能器的工作原理与故障分析 (1)蓄能器的工作原理。imd热压成型机广泛用于汽车行业的零配件加工及各行业多种产品的定型、冲边、校正及制鞋、手袋、橡胶、模具、轴类、轴套类零件的压装、压印成型、板材...
2023-02-15电话:0769-22253115 23113616
地址:东莞市东城区温塘砖窰工业区四横路116号